Search results for query: *

Talking about original equipment 14 inch wheels here. In 1971 - Do the W23 Road Wheel and the Rallye wheel use the same style and width of beauty ring. Any pictures would be helpful. Thanks Steve

I did try to find the source/article I read but no luck finding it - so I thought I should ask here. I did the ammeter bypass under the hood with a large wire from the alternator direct to the starter relay terminal. I left all the original wires/ammeter connected. I installed a 12V LED...

Do factory fitted Shaker hood cars have lighter hinge springs because of the large hole cut in the hood for the Shaker? If so what are the differences.

Hi all. I read on another post about the desirability of the wide mouth pin style brake callipers. Can anyone clue me in to what makes them desirable. Do they work better? Were only made for a short time? Just curious. Thanks Steve

Hi all. I was told by a guy that adding ZDDP additive to oil would not work as it separated out from the oil and lay in the bottom of the sump and did not mix with your oil. However I went ahead anyway as I had a little plan and tons of Castrol oil I won at car shows that I wanted to use up...

Hi. Is the original finish on the trunk latch plate attached to the trunk lid painted or zinc? I have researched in books and online and I see both. Thanks Steve

Hi. I bought this NOS piece a while ago. I thought it was a headlight on buzzer but the one fitted to my car has only two terminals. The new part has 3 terminals. Perhaps it is a horn relay? If anyone has a parts book could you check on this for me. Thanks Steve

I saw a factory diagram which showed a small square sealing adhesive strip applied to the cowl top to seal a hole that is partially under the cowl rubber seal. The hole is in the upper cowl panel somewhere near the last two clips on the outside of the curve in the rubber on both sides. I cannot...

I recently rebuilt my disc brake proportioning valve with a kit I purchased off Muscle Car Research. I found their website very informative on how to identify what valve I had, and how to strip and re-assemble it. The kits are very reasonably priced/good quality and well worth purchasing. The...

Hi I am looking for a pair of black kick panels in good to excellent condition. Must be original Chrysler Corp not repro. If you can ship international would be appreciated. If not I can do US address and PayPal. Thanks

Year One has full quarter panel and skins for sale. They do not say - but are they made by AMD?

Hi I am looking for a pair of black kick panels in good to excellent condition. Must be original Chrysler Corp not repro. If you can ship international would be appreciated. If not I can do US address and PayPal. Thanks

Hi. I am looking for an original Passengers (RH) side black A pillar trim for a 1971 onwards car. The lower screw is higher up the trim than the 1970 part. Only interested in original part in good condition Can do Pay Pal and US shipping address.

If the link works check this out Richard Holdener compares a 340 six pack to several other muscle motors. I liked it and the 340 does well.

I am thinking about purchasing a solid lifter Hughes cam and was wondering if any of you had run one in a 340 motor. Or any Mopar engine I guess. What did you think of it? I do like Comp Cams grinds. Have you run one and then fitted some other brand that went better or worse? Any relevant...

I am after the two steel bent plates that connect a 340 block to the engines mounts. I want LH and RH set. I would need you to have PayPal and be prepared to go to the post office and ship to me in New Zealand. If you live on the West Coast it would be good.

Question What is the difference between a Rottweiler and your wife? Answer A Rottweiler will eventually let go.

I see several parts sellers have the polyurethane upgraded engine mount sets. Looking to ask if they are worth buying. Vibration issues? Fitment problems?

How much, if any, do you think a car with the original engine and transmission is worth over a car that they have gone? I live in New Zealand were these things are not that important to most buyers. However I am curious to find out if it would be a factor in the USA. As a baseline assume we are...

Who sells or makes the best reproduction engine mount? I do not mean urethane or along those lines I mean rubber like stock. I fitted an Anchor one and it is reasonable but I wondered if there is better out there.