• Welcome to For E Bodies Only !

    We are a community of Plymouth Cuda and Dodge Challenger owners. Join now! Its Free!

77 Dodge 440 W200 long bed Club cab Located in Ca. $1,500 obo

Status
Not open for further replies.

EbodyLuv

Member
Joined
Dec 13, 2012
Messages
9
Reaction score
1
Location
San Jose, Ca
Rating - 0%
0   0   0
Contact seller
I'm on the hunt for a E-Body and need the driveway space. :)

***Update, hit the DMV this morning, registration is now current, took it off PNO, now currently registered until July 2013***

Dodge Powerwagon Club cab. Been a great work truck. Ugly but everything works except the A/C, its all there but it leaks somewhere, most likely the compressor. ~90k original miles with #'s match engine and trans.

440 ci engine
Dana 60 rear with limited slip
4:10 gears front and rear
120 amp charging system

Lots replaced, new drums and shoes, orange box ECU, carb rebuilt, Milodon HD waterpump, alternator, V regulator, fuel pump, tires ($800), belts, hoses, just about all usual wear items, plus new carpet and steering wheel.

Bonus:
Smitty front bumper
Hella H4 headlights and Hella H3 driving lights
Receiver for tow hitch
Factory tach and vacuum/volt gauge combo
Factory underbed tool box (needs to be welded in)
Set of headers included, not installed
New inner and outer window scraper, not installed
Holley Projection, 2 barrel, will include if wanted,
needs fuel pump, not installed
I have various other new/used parts for it too, badges, trim, stuff like that

Needs:
Alignment
Left Front rotor and both sets of pads
Grommet on top of gas tank for line that goes to charcoal canister. This is all it needs to pass smog, my girlfriend pirated it to smog her Ramcharger and its too much of a pain in the butt to drop the tank on the RC to get it back.
Needs front and rear main seals and VC gaskets.

On current Non-Op but I'm going to re-register it 12/17. Cool truck, has taken me and my dirt bikes everywhere, and hauled many a project bike home.

408-315-1670 txt OK or email ryouga_76@yahoo.com Neil

2012-05-13_17-48-34_473.jpg


20120715_134228_zpsdf65ad79.jpg


20120715_134307_zps1fc608d0.jpg


20120715_134326.jpg


2_IMAG0146.jpg
 
Last edited:

68427vette

Well-Known Member
Joined
Jan 27, 2011
Messages
89
Reaction score
2
Rating - 0%
0   0   0
great truck,, all the good stuff is out west.. dry:angryfire:

Bonus:
Smitty front bumper
Hella H4 headlights and Hella H3 driving lights
Receiver for tow hitch
Factory tach and vacuum/volt gauge combo
Factory underbed tool box (needs to be welded in)
Set of headers included, not installed
New inner and outer window scraper, not installed
Holley Projection, 2 barrel, will include if wanted,
needs fuel pump, not installed
I have various other new/used parts for it too, badges, trim, stuff like that

Needs:
Alignment
Left Front rotor and both sets of pads
Grommet on top of gas tank for line that goes to charcoal canister. This is all it needs to pass smog, my girlfriend pirated it to smog her Ramcharger and its too much of a pain in the butt to drop the tank on the RC to get it back.
Needs front and rear main seals and VC gaskets.

On current Non-Op but I'm going to re-register it 12/17. Cool truck, has taken me and my dirt bikes everywhere, and hauled many a project bike home.

408-315-1670 txt OK or email ryouga_76@yahoo.com Neil

2012-05-13_17-48-34_473.jpg


20120715_134228_zpsdf65ad79.jpg


20120715_134307_zps1fc608d0.jpg


20120715_134326.jpg


2_IMAG0146.jpg
[/QUOTE]
 

EbodyLuv

Member
Joined
Dec 13, 2012
Messages
9
Reaction score
1
Location
San Jose, Ca
Rating - 0%
0   0   0
Well, I'll give this one more go, it seems even rusty E body shells are out of my price range these days, I gotta start playing the lotto, lol! Anyways, all above plus the following for $2,250! Or trade for E-B-A-C body!

440 engine, magged, blueprinted, balanced. Steel crank, LY rods, Speedpro +.030 forged pistons, L2355F.
Peggy's sit .019" down in the hole, so a Cometic .027" ML gasket with Edelbrock heads will net you .046" quench at 10:1 compression. The right cam and intake combo can make you a fun street motor capable of 500 hp, or one heck of a stump puller to drop in the PW. Heads, gaskets, cam and intake not included.

Also, SFI approved damper, 3" I/O Hooker Aero Chamber muffs, Edelbrock air cleaner with 4" tall K&N filter, a set of the cool early metal door cards, and a bare standard bore 400 with main caps ready for your stroker project. Over $2,500 in the shortblock alone so it's like getting a deal on it, and getting a free truck and a bunch of parts to boot. Any takers? ;)

20121228_151703-1.jpg


20130102_215159.jpg


20121229_171213.jpg


20121229_171238.jpg


20121229_171201.jpg


20121228_151703.jpg
 

DetMatt1

Well-Known Member
Joined
May 13, 2009
Messages
7,988
Reaction score
2,157
Location
Metro Detroit
Rating - 100%
6   0   0
Man that's a hell of a deal! I'm almost glad that truck is too far from me, if it were closer I would have no choice but to buy it and that's the last thing I need!
 

jfreakofkorn

Well-Known Member
Joined
Apr 27, 2012
Messages
111
Reaction score
7
Location
us of a
Rating - 0%
0   0   0
Solid looking truck ....

Good luck with the sale .....

And I agree with DetMatt1 ..... If it was closer ..... Would have a sale ...
 
Status
Not open for further replies.
Back
Top